សេចក្តីផ្តើម
The NVX NSW102v3 is a high-performance 10-inch car subwoofer designed to deliver powerful and accurate bass. This N-Series subwoofer features robust construction and advanced components for an immersive audio experience in your vehicle. This manual provides essential information for the proper installation, operation, and maintenance of your subwoofer.
រូបភាព៖ ខាងមុខ view of the NVX NSW102v3 10-inch subwoofer, showcasing the cone and surround.
លក្ខណៈសំខាន់ៗ៖
- ការសម្តែងបាសដ៏មានឥទ្ធិពល៖ Delivers up to 1000W peak and 500W RMS power for deep, resonant bass.
- Accurate Sound Reproduction: Equipped with an enhanced pressed paper cone, high-roll foam surround, and a 2.0" high-temperature copper voice coil for minimal distortion and maximum clarity.
- Durable & Efficient Design: Features a stamped steel vented basket with NVX logo, 112 oz. double-stacked ferrite magnet, and protective rubber boot for reliable, long-lasting performance.
- ការឆ្លើយតបប្រេកង់ធំទូលាយ៖ Offers a frequency range of 20-200 Hz, a resonance frequency (Fs) of 38.67 Hz, and a sensitivity of 85 dB for dynamic bass.
- ជម្រើសដំឡើងដែលអាចបត់បែនបាន៖ Compatible with sealed enclosures (0.60 cubic feet) and ported enclosures (1.5 cubic feet).
ព័ត៌មានសុវត្ថិភាព
Always observe the following safety precautions during installation and operation to prevent injury or damage to the equipment:
- ផ្តាច់ខ្សែអវិជ្ជមានរបស់ថ្មរថយន្តចេញ មុនពេលចាប់ផ្តើមការងារអគ្គិសនីណាមួយ។
- Ensure all wiring is correctly routed and secured to prevent pinching or damage.
- ប្រើខ្សែរង្វាស់សមស្របសម្រាប់ការតភ្ជាប់ថាមពល ដី និងឧបករណ៍បំពងសំឡេង។
- Avoid installing the subwoofer in locations where it may obstruct vehicle operation or safety devices.
- ការប៉ះពាល់នឹងកម្រិតសម្ពាធសំឡេងខ្ពស់រយៈពេលយូរអាចបណ្តាលឱ្យខូចខាតដល់ការស្តាប់ជាអចិន្ត្រៃយ៍។ សូមប្រុងប្រយ័ត្ននៅពេលកែតម្រូវកម្រិតសំឡេង។
- ប្រសិនបើអ្នកមិនប្រាកដអំពីជំហានដំឡើងណាមួយទេ សូមពិគ្រោះជាមួយអ្នកជំនាញដំឡើងឧបករណ៍អូឌីយ៉ូរថយន្ត។
ការដំឡើងនិងការដំឡើង
សេចក្តីណែនាំអំពីការបិទភ្ជាប់៖
The performance of your subwoofer is highly dependent on the enclosure it is installed in. The NVX NSW102v3 is designed to perform optimally in the following enclosure types and volumes:
- ឯករភជប់បិទជិត៖ 0.60 cubic feet (net internal volume)
- ឯករភជប់ចល័ត៖ 1.5 cubic feet (net internal volume, excluding port and subwoofer displacement)
Ensure the enclosure is constructed from sturdy material and is airtight (for sealed) or properly tuned (for ported) to achieve the best sound quality and prevent damage to the subwoofer.
ការដំឡើងឧបករណ៍បំពងសំឡេង៖
Carefully place the subwoofer into the mounting hole of your enclosure. Ensure the mounting holes on the subwoofer frame align with the pre-drilled holes on the enclosure. Use appropriate screws to secure the subwoofer firmly. Do not overtighten, as this can strip the mounting holes or damage the frame.
រូបភាព៖ ចំហៀង view of the NVX NSW102v3 subwoofer, illustrating the mounting flange and terminal connections.
Wiring Configurations (Dual 2-Ohm Voice Coils):
The NSW102v3 features dual 2-Ohm voice coils, offering flexibility in wiring to achieve different impedance loads for your ampឧបករណ៍សង្គ្រោះបឋម។ ត្រូវប្រាកដជានិច្ចថាអ្នក ampឧបករណ៍បំលែងមានស្ថេរភាពនៅអ៊ីមផេដង់ដែលបានជ្រើសរើស។
រូបភាព៖ Close-up of the NVX NSW102v3 subwoofer's push terminals, showing positive and negative connections for each voice coil.
- បន្ទុក 4-អូម (ខ្សែភ្លើងស៊េរី):
ភ្ជាប់ខ្សែវិជ្ជមាននៃឧបករណ៍បញ្ជូនសំឡេង 1 ទៅខ្សែអវិជ្ជមាននៃឧបករណ៍បញ្ជូនសំឡេង 2។ បន្ទាប់មក ភ្ជាប់ amplifier's positive output to the remaining positive terminal of Voice Coil 2, and the amplifier's negative output to the remaining negative terminal of Voice Coil 1. This configuration results in a 4-Ohm load, suitable for many mono ampអ្នករស់រានមានជីវិត
- បន្ទុក 1-អូម (ខ្សែភ្លើងប៉ារ៉ាឡែល):
Connect the positive terminals of Voice Coil 1 and Voice Coil 2 together. Connect the negative terminals of Voice Coil 1 and Voice Coil 2 together. Then, connect the ampទិន្នផលវិជ្ជមានរបស់ឧបករណ៍បំលែងទៅកាន់ស្ថានីយវិជ្ជមានរួមបញ្ចូលគ្នា និង amplifier's negative output to the combined negative terminals. This configuration results in a 1-Ohm load, typically used with high-current, 1-Ohm stable mono ampអ្នករស់រានមានជីវិត
យោងទៅរបស់អ្នក។ amplifier's manual for compatible impedance loads. Incorrect wiring can damage both the subwoofer and the ampកាន់តែចាស់។
សេចក្តីណែនាំប្រតិបត្តិការ
Initial Use and Break-in Period:
Allow a break-in period of approximately 10-20 hours of moderate use before operating the subwoofer at high volumes. This allows the suspension components (surround and spider) to loosen up and reach their optimal performance characteristics. During this period, avoid playing the subwoofer at maximum volume or with excessive bass boost.
ការគ្រប់គ្រងថាមពល៖
The NVX NSW102v3 is rated for 500 Watts RMS (Root Mean Square) and 1000 Watts Peak power. RMS power is the continuous power the subwoofer can handle, while peak power is the maximum power it can handle for short bursts. To ensure longevity and optimal performance, it is recommended to match the subwoofer with an amplifier that delivers approximately 500 Watts RMS at the chosen impedance load.
Avoid exceeding the RMS power rating for extended periods, as this can lead to overheating and damage to the voice coil. Ensure your amplifier's gain is set correctly to prevent clipping, which can also damage the subwoofer.
ថែទាំ
Proper maintenance will ensure the longevity and performance of your NVX subwoofer.
- ការសម្អាត៖ Use a soft, dry cloth to wipe down the subwoofer cone and surround. Avoid using harsh chemicals, solvents, or abrasive cleaners, as these can damage the materials.
- អធិការកិច្ច៖ Periodically inspect the subwoofer for any signs of damage, such as tears in the cone or surround, loose connections, or unusual odors. Address any issues promptly.
- បរិស្ថាន៖ Ensure the subwoofer is installed in a dry environment, protected from direct sunlight and extreme temperatures.
ការដោះស្រាយបញ្ហា
ប្រសិនបើអ្នកជួបប្រទះបញ្ហាជាមួយឧបករណ៍បំពងសំឡេងរបស់អ្នក សូមមើលជំហានដោះស្រាយបញ្ហាទូទៅខាងក្រោម៖
| បញ្ហា | មូលហេតុដែលអាចកើតមាន | ដំណោះស្រាយ |
|---|---|---|
| គ្មានសំឡេងពី Subwoofer |
|
|
| សំឡេងខូច |
|
|
| បាសខ្សោយ ឬមានសំឡេងបាស |
|
|
| សំឡេងស៊ុបវូហ្វើរឡើងកម្ដៅខ្លាំងពេក |
|
|
លក្ខណៈបច្ចេកទេស
The following table outlines the key technical specifications for the NVX NSW102v3 10-inch Dual 2-Ohm Car Subwoofer:
| លក្ខណៈ | ការបញ្ជាក់ |
|---|---|
| ឈ្មោះម៉ូដែល | NSW102v3 |
| ប្រភេទឧបករណ៍បំពងសំឡេង | ឧបករណ៍បំពងសំឡេង |
| ទំហំធុងបាស | ៤.៧៥ អ៊ីញ |
| អង្កត់ផ្ចិត Woofer | ៤.៧៥ អ៊ីញ |
| ការកំណត់រចនាសម្ព័ន្ធឧបករណ៍បញ្ជូនសំឡេង | ទ្វេ 2-អូម |
| Speaker Maximum Output Power (Peak) | 1000 វ៉ាត់ |
| ការគ្រប់គ្រងថាមពល RMS | 500 វ៉ាត់ |
| ការឆ្លើយតបប្រេកង់ | 20-200 ហឺត |
| ប្រេកង់ Resonance (Fs) | 38.67 ហឺត |
| ភាពរសើប | 85 dB |
| ទម្ងន់មេដែក | 112 oz. (double-stacked ferrite) |
| សម្ភារៈធ្វើពីកោណ | Enhanced Pressed Paper |
| សម្ភារៈជុំវិញ | High-Roll Foam |
| សម្ភារៈ Voice Coil | High-temperature Copper |
| ប្រភេទកន្ត្រក | Stamped Steel Vented |
| បរិមាណស្រោមបិទជិតដែលបានណែនាំ | 0.60 ហ្វីតគូប |
| Recommended Ported Enclosure Volume | 1.5 ហ្វីតគូប |
| ទំងន់ធាតុ | 14.4 ផោន |
| ទំហំផលិតផល (D x W x H) | 5.7"D x 6.5"W x 5.7"H |
Note: The listed product dimensions may refer to packaging or a specific component. For precise mounting depth and cutout dimensions, please refer to the product's technical drawing or contact NVX support.
ព័ត៌មានធានា
The NVX NSW102v3 subwoofer is covered by a Limited Warranty. For detailed information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your purchase or visit the official NVX webគេហទំព័រ។ រក្សាភស្តុតាងនៃការទិញរបស់អ្នកសម្រាប់ការទាមទារធានា។
គាំទ្រ
For technical assistance, troubleshooting, or any questions regarding your NVX NSW102v3 subwoofer, please contact NVX customer support. You can typically find contact information on the official NVX webគេហទំព័រ ឬតាមរយៈអ្នកចែកបៀដែលមានការអនុញ្ញាតរបស់អ្នក។